Lenovo ThinkCentre M83 Desktop: ripristino dopo POST/BIOS update fallito

Purtroppo talvolta può capitare che un aggiornamento BIOS fallisca rendendo il computer non più utilizzabile. In questi mi è capitato di verificare una situazione simile con un computer desktop Lenovo ThinkCentre M83 durante l’installazione del pacchetto Flash BIOS update – ThinkCentre E93, M73p, M83, M93, M93p, ThinkStation E32, ThinkStation P300 Ver. FBKTD2A 03 Jul 2018 scaricabile dal seguente M83 Desktop (ThinkCentre) – Driver & Software.

Nel mio caso dopo avere installato l’aggiornamento BIOS eseguendo il pacchetto d’installazione dal sistema operativo ovvero il Windows BIOS Setting Tool [fbjwd2usa.exe] il computer si è riavviato bloccandosi su una schermata nera con la scritta Lenovo. A nulla è servito provare a togliere l’alimentazione e premere per 30 secondi il pulsante d’accensione o a rimuovere la batteria CMOS per 60 secondi.

Lenovo prevedere però una procedura di ripristino in seguito ad aggiornamenti POST/BIOS falliti descritta nell’Hardware Maintenance Manual (HMM) – ThinkCentre M83, M93, M93p tramite cui è possibile eseguire nuovamente l’aggiornamento del firmware tramite un CD su cui è stata masterizzata la Flash UEFI BIOS update (CD ISO image version) [fbj9d2usa.iso]. Tale procedura prevede l’avvio del sistema dopo aver impostato il jumper Clear CMOS in modalità Recovery per poter eseguire l’aggiornamento BIOS tramite CD all’avvio, terminato l’aggiornamento il computer si arresta ed è possibile ripristinare il jumper Clear CMOS in modalità standard.

Di seguito la procedura descritta nell’Hardware Maintenance Manual (HMM) – ThinkCentre M83, M93, M93p:

Recovering from a POST/BIOS update failure

If the power to your computer is interrupted while the POST and BIOS is being updated, your computer might not restart correctly. If this happens, perform the following procedure to recover from the POST and BIOS update failure. This procedure is commonly called Boot-block Recovery.

  1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer.
  2. Open the computer cover. See “Removing the computer cover” on page 93.
  3. Remove the hard disk drive. See “Replacing the primary hard disk drive” on page 126
  4. Locate the Clear CMOS /Recovery jumper on the system board. See “Locating parts on the system board” on page 90.
  5. Remove any cables that impede access to the Clear CMOS /Recovery jumper.
  6. Move the jumper from the standard position (pin 1 and pin 2) to the maintenance position (pin 2 and pin 3).
  7. Reconnect any cables that were disconnected and reinstall the PCI card if removed.
  8. Close the computer cover and reconnect the power cords for the computer and monitor to electrical outlets. See “Completing the parts replacement” on page 156.
  9. Turn on the computer and then insert the POST and BIOS update (flash update) disc into the optical drive. Wait a few minutes. Then, the recovery session begins. The recovery session will take two to three minutes. During this time, a warning message will be displayed and no action is needed from you.
  10. After the recovery session is completed, there will be no video, and your computer will automatically turn off.
  11. Repeat step 1 through step 5.
  12. Move the Clear CMOS /Recovery jumper back to the standard position (pin 1 and pin 2).
  13. Reconnect any cables that were disconnected and reinstall the PCI card if removed.
  14. Close the computer cover and reconnect any cables that were disconnected.
  15. Turn on the computer to restart the operating system.

Locating parts on the system board

Note: Your computer comes with one of the following system boards.

Figure 18 “System board part locations” on page 91 shows the locations of the parts on the system board.

Terminato l’aggiornamento il computer si è riavviato presentando un errore di configurazione BIOS che si è risolto caricando le impostazioni di default BIOS e salvandole.